EDIS coil connector

General Chat About Electrics, And Ignition Systems.

Moderator: phpBB2 - Administrators

Post Reply
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

EDIS coil connector

Post by DaveEFI »

Managed to break one of my EDIS 8 (4) coil LT connectors - the earlier type with the plastic arms on the side to lock it. Can find the later 'oval' type new, but not the earlier one. A good secondhand one would do.
Unless the later type fits?


Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
User avatar
SimpleSimon
Knows His Stuff
Knows His Stuff
Posts: 620
Joined: Mon Apr 25, 2011 10:36 pm
Location: East Sussex

May be of help

Post by SimpleSimon »

Are you saying you need one? if so I can help you,pick up from SE London area FOC 8-)
scudderfish
Site Admin
Site Admin
Posts: 559
Joined: Sat Feb 28, 2009 6:53 pm
Location: Harpenden, Hertfordshire

Post by scudderfish »

Failing that, you can buy them here http://www.megasquirt-v8.co.uk/generic_parts.php
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

scudderfish wrote:Failing that, you can buy them here http://www.megasquirt-v8.co.uk/generic_parts.php
The pic on their site is of the later type which several sell. Unless I've missed something?
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
scudderfish
Site Admin
Site Admin
Posts: 559
Joined: Sat Feb 28, 2009 6:53 pm
Location: Harpenden, Hertfordshire

Post by scudderfish »

DaveEFI wrote:
scudderfish wrote:Failing that, you can buy them here http://www.megasquirt-v8.co.uk/generic_parts.php
The pic on their site is of the later type which several sell. Unless I've missed something?
They fit the Gen 1 coil packs a bit further down the page.
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

scudderfish wrote:
DaveEFI wrote:
scudderfish wrote:Failing that, you can buy them here http://www.megasquirt-v8.co.uk/generic_parts.php
The pic on their site is of the later type which several sell. Unless I've missed something?
They fit the Gen 1 coil packs a bit further down the page.
They are indeed for the early coil. But of a a different design. My original Ford ones have two plastic locking levers on the outside of the body - these use an sprung wire arrangement similar to the junior power ones as used on injectors, etc.
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
scudderfish
Site Admin
Site Admin
Posts: 559
Joined: Sat Feb 28, 2009 6:53 pm
Location: Harpenden, Hertfordshire

Post by scudderfish »

DaveEFI wrote: They are indeed for the early coil. But of a a different design. My original Ford ones have two plastic locking levers on the outside of the body - these use an sprung wire arrangement similar to the junior power ones as used on injectors, etc.
They've changed since I bought some earlier this year as mine have plastic levers on them.

Regards,
Dave
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

scudderfish wrote:
DaveEFI wrote: They are indeed for the early coil. But of a a different design. My original Ford ones have two plastic locking levers on the outside of the body - these use an sprung wire arrangement similar to the junior power ones as used on injectors, etc.
They've changed since I bought some earlier this year as mine have plastic levers on them.

Regards,
Dave
Yes - that's what confused me. I remember seeing identical ones to my originals on sale. And not knowing what the later coil used didn't help. ;-)
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
Nigel B
Forum Contributor
Forum Contributor
Posts: 45
Joined: Thu Feb 07, 2008 5:03 pm
Location: Costa Del Haslemere

Post by Nigel B »

Someone call :lol:

Ok

The lead ends I do at the moment are for the Ford Generation 1 Coil pack, obviously 2 x for a V8, these packs are noticebale as they have a "Collar" where the lead end goes on around 15mm from the top. This allows the 2 "Prongs" of the plastic Cage to Lock On to the ring, as thus, for the application I work mainly in (4x4 off road racing) these give a near 100% waterproof connection.

However I have supplied a huge amount of these to track cars and other engines, where peeps have switched to the old G1 coils over the later type, the later type has no ring and is just a Push fit at the coil end, this can and does not give such a "Locked on" solution, plus the early coils rarely fail (Pattern ones excluded from the prev statement !) - ie Buy second hand Motorcraft or Ford only.

Here is a pic of the units I have

The brass terminals - both sides for clarity, the 90 degree rubber boot, and the clip to lock in in.

Image

These units will NOT fit the later smooth fitting Type 2, these use a completely differing system, and are indentifyable by a "Pin" in the centre and base of the insides of the output tower, not even the brasses above fit.

Hope this helps

Nige
Lover of V8s and Megasquirt - Now with a shop for all things Megasquirt - & V8 - Brackets parts and complete systems www.megasquirt-v8.co.uk
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

Sorry - we're at cross purposes here. It's the LT (12v) connector I'm talking about, not the HT (plug lead) ones. I've got lots of the latter. :D
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
User avatar
SimpleSimon
Knows His Stuff
Knows His Stuff
Posts: 620
Joined: Mon Apr 25, 2011 10:36 pm
Location: East Sussex

Post by SimpleSimon »

DaveEFI wrote:Sorry - we're at cross purposes here. It's the LT (12v) connector I'm talking about, not the HT (plug lead) ones. I've got lots of the latter. :D
Yes an I have one less :lol: good heads up Nigel B though,I see these recently while scooting round the net :D
TVR Chimaera RV8 Mods & Megasquirt
Nigel B
Forum Contributor
Forum Contributor
Posts: 45
Joined: Thu Feb 07, 2008 5:03 pm
Location: Costa Del Haslemere

Post by Nigel B »

Oh......THOOOOOOOOOSE :lol:

As in :

Image

??

Yes, I do these

Brand new genuine Ford (has Ford logo on them) hideously expensive IMHO
but not yet on my website - are £17 each, £15 each for here with Free UK P&P ?

Come with 3 x gromets and 3 x pins each and fit both types of Coil Pack units - PM me if you wnat them, esp at the price above,
DO NOT buy off my website even when I get around to listing them !


Nige :wink:
Lover of V8s and Megasquirt - Now with a shop for all things Megasquirt - & V8 - Brackets parts and complete systems www.megasquirt-v8.co.uk
DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

That's the one. As I said it's a different design from the originals I have. Which have two clips, one either side, rather like the plug lead ones.
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y
Nigel B
Forum Contributor
Forum Contributor
Posts: 45
Joined: Thu Feb 07, 2008 5:03 pm
Location: Costa Del Haslemere

Post by Nigel B »

piccies ?

both of plug and coil pack ?

Nige
Lover of V8s and Megasquirt - Now with a shop for all things Megasquirt - & V8 - Brackets parts and complete systems www.megasquirt-v8.co.uk
Post Reply

Return to “Electrical & Ignition Area”