Turbo & Blow Through Carb resources

[mrmad]

nothing serious mate just an axel bearing
i want to try and hook this b@tch up this year
so im swithing to a fully built fabricated ford 9" built by geoff hauser £4500
jay

[mrmad]

Hi Jay,
glad to see you have rejoined us mate

cheers mate sorry its been a while
this car keeps taking the cash so im allways out earning it
jay

[IainB]

hi iain
i got my carb custom built to my engine by these guys http://www.csucarbs.com/ the guys name is kevin and all i can say is that he knows his stuff when i was on the dyno he was on hand for advice
not had any problems with his carb at all
here allso is a link to doin a carb your self very use full http://www.hangar18fabrication.com/blowthru.html

hope this helps

Cheers Jay
Had a look at both those sites already, think it was CSU who do the hats/bonnets also? (have been recommended them off the american site)
Need to get the car back from its extended holiday first, then start working things out
Wont be going mad with the boost as im not looking for silly HP - ideally want an engine thats not going to need loads of work after every run and has good road manners - time will tell

P.S. good to see you back

[ian.stewart]

nothing serious mate just an axel bearing
i want to try and hook this b@tch up this year
so im swithing to a fully built fabricated ford 9" built by geoff hauser £4500
jay

I hope thats fully fitted

[mrmad]

hi iain
i got my carb custom built to my engine by these guys http://www.csucarbs.com/ the guys name is kevin and all i can say is that he knows his stuff when i was on the dyno he was on hand for advice
not had any problems with his carb at all
here allso is a link to doin a carb your self very use full http://www.hangar18fabrication.com/blowthru.html

hope this helps

Cheers Jay
Had a look at both those sites already, think it was CSU who do the hats/bonnets also? (have been recommended them off the american site)
Need to get the car back from its extended holiday first, then start working things out
Wont be going mad with the boost as im not looking for silly HP - ideally want an engine thats not going to need loads of work after every run and has good road manners - time will tell

P.S. good to see you back

thanks its good to b e back
here is another site that you may of seen they do very nice hats http://www.superiorairflow.com/
jay

[mrmad]

nothing serious mate just an axel bearing
i want to try and hook this b@tch up this year
so im swithing to a fully built fabricated ford 9" built by geoff hauser £4500
jay

I hope thats fully fitted

no mate i will fit it.
this is the list of parts
competition engineering fabricated ford 9" housing and back brace
strange 31 spline shafts
big bearing strange ford housing ends and bearings
strange nodular iron s series third member
daytona pinion support
1350 pinion
strange third member bearings
strange 325 gears
aerospace engineering 4 pot billet drag race rear brakes
tru trac differential
all braided brake lines
competion engineering brackets for four link
all the fabrication
power coating the whole axel
compleat new 1350 propshaft
strange double adjustable coilovers and springs

i have taken the 8" off the car he is replicating the mounts on that

[smokeonthewater]

you can of course run the carb in a closed plenum, so pressure is equalised and you dont need a special carb, but you do need rising rate fuel pressure so you dont push the fuel back along the fuel line,

What do you mean by a closed plenum?

[kiwicar]

you put the carb in an enclosed box and presurise that, with a feed off to the fuel regulator.
Mike