hi all peeps

Please introduce yourself to everyone and say hi :-)

Moderator: phpBB2 - Administrators

Post Reply
jaybe
Newbie
Newbie
Posts: 12
Joined: Wed Aug 21, 2013 7:43 pm

hi all peeps

Post by jaybe »

hello all I just joined the site today (21/8/13) I stumbled upon this site when trying to identify my rover V8 engine no 1051cr 48104528B . ive looked on rimmer bothers site but can't find engine number ending in B only A . my plan is to do engine swap on my TR7 . I need to get my hands on a sd1 bellhousing to mate with my LT77 5 speed box but they are rare now days also I need timingcover/water pump housing and pump they are selling pumps on certain auction site . well i will tell the rest later as this is my introduction so best keep it short . :P :P :?:



User avatar
Rossco
Moderator Gold
Moderator Gold
Posts: 850
Joined: Sun Nov 19, 2006 11:33 am
Location: Too many to even keep count

Post by Rossco »

Jaybe, welcome to the mad house

I'm sure the peeps here can help you out.

harvey
Knows His Stuff
Knows His Stuff
Posts: 452
Joined: Fri Feb 13, 2009 3:43 pm

Re: hi all peeps

Post by harvey »

jaybe wrote:48104528B
P6B 3500S (manual) engine, 10.5:1 with a lipseal rear main seal, circa 1973/4 I would guess.

User avatar
Rossco
Moderator Gold
Moderator Gold
Posts: 850
Joined: Sun Nov 19, 2006 11:33 am
Location: Too many to even keep count

Post by Rossco »

There you go.......another indication of just how lonely those of us that frequent this form actually are

:lol:

DaveEFI
Gold Member
Gold Member
Posts: 4603
Joined: Fri Feb 26, 2010 4:27 pm
Location: SW London, UK

Post by DaveEFI »

The 10.5:1 CR means it is a very early engine - they were only made until the early '70s. Later heads are rather better. (the pistons set the CR, unless the head has been planed.
Dave
London SW
Rover SD1 VDP EFI
MegaSquirt2 V3
EDIS8
Tech Edge 2Y

jaybe
Newbie
Newbie
Posts: 12
Joined: Wed Aug 21, 2013 7:43 pm

Post by jaybe »

thank you Harvey for the info :D . so I guess I can interchange parts with other 3.5 engines :?: ? how on earth did you manage to find out what engine it is as I looked everywhere :shock: . again many thanks :D . just need to source the parts I need now :( glad I found this site :D

jaybe
Newbie
Newbie
Posts: 12
Joined: Wed Aug 21, 2013 7:43 pm

Post by jaybe »

well thank you too dave efi :D so as I haven't even started engine strip down I should look out for some SD1 heads ? wont this decrease the comp ratio or increase it :?: don't think the wifes gonna be happy with me spending more on my project car as we both are out of work at mo . and iam maxed out on credit cards . :roll: come on lottery let me win so I can build my workshop with ramp and all that's needed . must admit if I had that I wouldn't need a house as I would be content on sleeping/living in there :lol: :lol: :lol:

harvey
Knows His Stuff
Knows His Stuff
Posts: 452
Joined: Fri Feb 13, 2009 3:43 pm

Post by harvey »

Rossco wrote:There you go.......another indication of just how lonely those of us that frequent this form actually are

:lol:
I don't know if I dare tell you that I didn't have to look that up either..... :lol:

jaybe
Newbie
Newbie
Posts: 12
Joined: Wed Aug 21, 2013 7:43 pm

Post by jaybe »

8-) wow bundle of knowledge . worth me getting to know you and rack your brain for info 8)

kiwicar
Forum Contributor
Forum Contributor
Posts: 5461
Joined: Sat Nov 18, 2006 5:00 pm
Location: Milton Keynes

Post by kiwicar »

Hi Rossco
I don't know what you are on about I am lots less lonely since I joined the forum I now have some friends! :lol: OK they have a fairly specialised interest range, but they are friends . . . . :oops:
Best regards
Mike
poppet valves rule!

jaybe
Newbie
Newbie
Posts: 12
Joined: Wed Aug 21, 2013 7:43 pm

Post by jaybe »

Rossco wrote:There you go.......another indication of just how lonely those of us that frequent this form actually are

:lol:


:D CHEER UP MATEjavascript:emoticon(':oops:') . LIFES TO SHORT :oops:
Image

Post Reply

Return to “Please Tell Us About Yourself”