My 16 valve GTi........
Moderator: phpBB2 - Administrators
My 16 valve GTi........
Here she is! a '78 MGB V8 GTi. Been working on it a few months now. Bit rusty in the usual places (Floors, Doors, Bonnet, Wings). Got big plans for her (She's called Brenda BTW) proposed
spec list (student loan dependant!) 3.5 EFI RR V8, Stage 1 heads, P&P inlet manifold, Modified plenum, Bigger injectors, KMS Engine Management (fuel only), Grumpy Cam, Rhodes lifter, Duplex timing chain, etc, etc.
The car itself with be completely stripped out, minimal chrome, no carpets or sound deadening, GRP bonnet, wings, Front ST spoiler, Rear Sebring, MGC bonnet, 2 bucket seats, thats it!
Imagine all draped in Ford Aquarius Blue Metallic, Mmmmm
Donations welcome
P.S. FAO Perry - I'll see you on the strip!
spec list (student loan dependant!) 3.5 EFI RR V8, Stage 1 heads, P&P inlet manifold, Modified plenum, Bigger injectors, KMS Engine Management (fuel only), Grumpy Cam, Rhodes lifter, Duplex timing chain, etc, etc.
The car itself with be completely stripped out, minimal chrome, no carpets or sound deadening, GRP bonnet, wings, Front ST spoiler, Rear Sebring, MGC bonnet, 2 bucket seats, thats it!
Imagine all draped in Ford Aquarius Blue Metallic, Mmmmm
Donations welcome
P.S. FAO Perry - I'll see you on the strip!
If it dont fit, force it. If it breaks, you needed a new one anyway!
I got the spoiler and all my fibreglass panels from the MGBHive. Although I was chatting to the bloke I bought my gearbox off and he used to work for honeyborne mouldings, who supply the hive. So I'll be going direct to them from now on!
If it dont fit, force it. If it breaks, you needed a new one anyway!
-
- Top Dog
- Posts: 2334
- Joined: Sat Aug 18, 2007 5:09 pm
- Location: Sidcup, Kent, UK
Nice project, if you haven't got a C bonnet yet, Honeybourne mouldings do a very good RV8 bonnet which is designed for clearance of the EFI plenum, mine was only £84.00 and good quality with all the fittings nicely bonded in, I also got the Sebring front and rear valences from them.
There's some pics of my car in the thread My MGBV8 a bit further down the page.
Good luck with the car, there's quite a few B's on the BBS now so if you need any advice you know where to come.
Kevin.
There's some pics of my car in the thread My MGBV8 a bit further down the page.
Good luck with the car, there's quite a few B's on the BBS now so if you need any advice you know where to come.
Kevin.
-
- Top Dog
- Posts: 2334
- Joined: Sat Aug 18, 2007 5:09 pm
- Location: Sidcup, Kent, UK
Kevin, I have also seen your car before! The RV8 bonnet looks cool, but I have my heart set on a C bonnet. I saw an alloy one at the Stoneleigh MG spares day and the chap wanted £600 notes for it! I'm still debating whether to blend in the rear valance or not?! Body Filler does weigh quite a bit!
If it dont fit, force it. If it breaks, you needed a new one anyway!
-
- Top Dog
- Posts: 2334
- Joined: Sat Aug 18, 2007 5:09 pm
- Location: Sidcup, Kent, UK
The Honeyborne rear valence is a very good fit, we just bonded and pop rivetted into position, there was very little filler used to blend it in.adikt wrote:Kevin, I have also seen your car before! The RV8 bonnet looks cool, but I have my heart set on a C bonnet. I saw an alloy one at the Stoneleigh MG spares day and the chap wanted £600 notes for it! I'm still debating whether to blend in the rear valance or not?! Body Filler does weigh quite a bit!
As yours is a rubber bumper you'll need the two extension pieces that go under the rear light if you haven't already got them. BeeHive have them and my bodywork guy bonded them on with liquid weld, I wasn't sure they be that solid but gave them a pull and they were solid as a rock.
Kevin.
I've got the two extension pieces (which way up do they go? One end seems wider?!) The valence seems about 1/2 inch wider than the car each side, although the car has been "messed around". I think i'll rivet it to pull it in then fill it.
If it dont fit, force it. If it breaks, you needed a new one anyway!
-
- Top Dog
- Posts: 2334
- Joined: Sat Aug 18, 2007 5:09 pm
- Location: Sidcup, Kent, UK
Just spotted that you haven't closed the chassis members where youv'e cut off the supports for the front rubber bumper, I assume you not going to leave them like that or water is going to get into the box section and it will rot very quickly.
Just cut some closing pieces and either weld or at least bond them on.
Kevin
Just cut some closing pieces and either weld or at least bond them on.
Kevin
They will get welded in, pumped with waxoyl and a stroke of seam sealer for good measure as soon as I get some more welding gas and a new regulator. The only job I can do without welding at the moment is fitting the front wings and it looked so good I had to take the pic! Money is very tight at the mo so no more goodies till student loan day in april!
If it dont fit, force it. If it breaks, you needed a new one anyway!
At least the back of the GT is the right colour
I'm liking the idea of the Blue mind. Sounds like its gonna be a screamer mate. Forget meeting me on the strip. Chod is the one who will be blowing all the B's away soon....
I've moved to Honeybourne as well now as they are by far the cheapest for placcy panels eh?
I'm liking the idea of the Blue mind. Sounds like its gonna be a screamer mate. Forget meeting me on the strip. Chod is the one who will be blowing all the B's away soon....
I've moved to Honeybourne as well now as they are by far the cheapest for placcy panels eh?
Perry Stephenson
MGB GT + Rover V8
9.62 @ 137.37mph
Now looking for 8 seconds with a SBC engine
Are you in the MG drag racing club? Would like to join......
Unfortunatly I only found out about honeybourne recently and I only have 1 panel left to buy although I cant really grumble about the Hive, very competitive prices and always friendly staff!
Unfortunatly I only found out about honeybourne recently and I only have 1 panel left to buy although I cant really grumble about the Hive, very competitive prices and always friendly staff!
If it dont fit, force it. If it breaks, you needed a new one anyway!
All you need to do to join the MG Drag Racing Club is turn up at one of our get togethers with your MG mate.
Then I class you as a member. Thats it really. I havent had time to update the website for ages but I've got half the words written so one of the chaps can update for me.
Then I class you as a member. Thats it really. I havent had time to update the website for ages but I've got half the words written so one of the chaps can update for me.
Perry Stephenson
MGB GT + Rover V8
9.62 @ 137.37mph
Now looking for 8 seconds with a SBC engine