how do i go about supercharging??
Moderator: phpBB2 - Administrators
how do i go about supercharging??
hey there, how would i go about supercharging my sierra?? i got a 3.5 V8 from a 1987 model range rover, was efi but now got holley 4 barrel carb, edelbrock headers, edelbrock pan filter, JWL inlet manifold.
im tryin to find out what steps i need to take to do a supercharger conversion, looking at also adding Nitros later. also where can i find an adequate charger for this,and what sort of output am i going to expect?? as she is at the moment, she's runnng approx 210bhp.
any other details you may need, just ask. many thanks peeps.
im tryin to find out what steps i need to take to do a supercharger conversion, looking at also adding Nitros later. also where can i find an adequate charger for this,and what sort of output am i going to expect?? as she is at the moment, she's runnng approx 210bhp.
any other details you may need, just ask. many thanks peeps.
http://www.v-8.org.uk/forum/viewtopic.php?t=3023 for supercharger if its still available.
Hello I have for sale my Sprintex S102, it is fully rebuild with new teflon coating rotors and supercharger casting.
S102 sprintex on 3.5 Rover V8 is good for 303BHP@6000RPM and 323FTLB@3500RPM. I have some set up figures (BHP/Torque) realised by DPR (Dennis Priddle) for Rover V8 3.5 with ignition timing value, CR and pulleys ratio. Also I have the map of brackets to bolt the supercharger on the rover V8 as the sprintex of EFI Haughins kit was bolted.
You can use this type of bracket for an blow throught installation.
Cheers.
Dimitri
S102 sprintex on 3.5 Rover V8 is good for 303BHP@6000RPM and 323FTLB@3500RPM. I have some set up figures (BHP/Torque) realised by DPR (Dennis Priddle) for Rover V8 3.5 with ignition timing value, CR and pulleys ratio. Also I have the map of brackets to bolt the supercharger on the rover V8 as the sprintex of EFI Haughins kit was bolted.
You can use this type of bracket for an blow throught installation.
Cheers.
Dimitri
Carburetor blow throught hat are avaiable on ebay :
http://cgi.cafr.ebay.ca/EFI-THROTTLE-BO ... dZViewItem
http://cgi.cafr.ebay.ca/EFI-THROTTLE-BO ... dZViewItem
-
- Newbie
- Posts: 3
- Joined: Thu Aug 13, 2020 2:50 pm
Re:
Wotland wrote: ↑Tue Mar 25, 2008 10:25 amHello I have for sale my Sprintex S102, it is fully rebuild with new teflon coating rotors and supercharger casting.
S102 sprintex on 3.5 Rover V8 is good for 303BHP@6000RPM and 323FTLB@3500RPM. I have some set up figures (BHP/Torque) realised by DPR (Dennis Priddle) for Rover V8 3.5 with ignition timing value, CR and pulleys ratio. Also I have the map of brackets to bolt the supercharger on the rover V8 as the sprintex of EFI Haughins kit was bolted.
You can use this type of bracket for an blow throught installation.
Cheers.
Dimitri
Good afternoon,
New to the forum, I came across this post hunting for info in the DPR conversions, myself and a mate have a running example of the 3.5 conversion. I’m interested to find more details of the particulars of the builds. The lower half of the inlet has been swapped for a Hotwire setup, and it’s currently running on a 3.9 map. Were now going to aftermarket to make the most of it.
Our engine is mounted in the rear of a unimog axled off-road buggy. Were running the forward facing the headers, which are now rear facing with the engine rotated.
Re: how do i go about supercharging??
Looks interesting - wouldn't mind seeing some more pictures of the buggy!
Chris.
Chris.
--
Series IIA 4.6 V8
R/R P38 4.6 V8
R/R L405 4.4 SDV8
Series IIA 4.6 V8
R/R P38 4.6 V8
R/R L405 4.4 SDV8
-
- Newbie
- Posts: 3
- Joined: Thu Aug 13, 2020 2:50 pm
Re: how do i go about supercharging??
Looks amazing - what actually is it?
Chris.
Chris.
--
Series IIA 4.6 V8
R/R P38 4.6 V8
R/R L405 4.4 SDV8
Series IIA 4.6 V8
R/R P38 4.6 V8
R/R L405 4.4 SDV8
-
- Newbie
- Posts: 3
- Joined: Thu Aug 13, 2020 2:50 pm
Re: how do i go about supercharging??
It’s a completely custom build, built for 5 gate euro type trialling. She’s running 42” tyres on unimog 404 axles, 4 wheel steer and several other tricks
- Ian Anderson
- Forum Contributor
- Posts: 2396
- Joined: Sun Nov 19, 2006 9:46 pm
- Location: Edinburgh
Re: how do i go about supercharging??
That looks like heaps of fun,
Owner of an "On the Road" GT40 Replica by DAX powered by 3.9Hotwre Efi, worked over by DJ Motors. EFi Working but still does some kangaroo at low revs (Damn the speed limits) In to paint shop 18/03/08.
-
- Newbie
- Posts: 1
- Joined: Sun Oct 25, 2020 11:33 pm
Re: how do i go about supercharging??
Hi, I have a Dennis Priddle DPR 1991 Classic Range Rover, was a 3.9 Vogue SE but converted by him to a 4.2 Sprintex supercharger, it does go well but I’d love any info on the DPR conversions if anyone has anything,
Phil.
Phil.