AP Clutch Listings

General Chat About Drivetrain & Transmission.

Moderator: phpBB2 - Administrators

Post Reply

Was this info useful?

YES?
5
100%
NO?
0
No votes
 
Total votes: 5

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

AP Clutch Listings

Post by Coops » Sun Jun 08, 2008 9:29 am

Thanks to marki for making this one document from the long list of pages i found,
BEWARE this is a big file,

http://www.v8forum.co.uk/docs/ap_clutches.pdf

Page 1 -> CARBON / CARBON CLUTCHES,
Page 18 -> SINTERED & CERAMETALLIC RACE CLUTCHES,
Page 49 -> SLAVE CYLINDERS, BEARINGS & STUDS,
Page 53 -> FORMULA CLUTCH KITS AND FLYWHEELS,
Page 56 -> HIGH PERFORMANCE CLUTCHES,
Page 63 -> HIGH PERFORMANCE CLUTCHES, Application List

Hope this is of some use to every one,


Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops » Sun Jun 08, 2008 10:13 am

rover v8 is page 71,
tvr page 72
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops » Wed Aug 18, 2010 9:37 pm

Back up online again now.
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops » Tue Jan 21, 2014 8:16 pm

I'm using a CP2394-60 cover & CP2346-4 friction plate with a spec of 339lbs/ft of torque, not sure how much longer it may last mind you :lol:

anyone mix and matched any of the AP clutches with any success?
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

BISH V8
Helpful or Confused
Helpful or Confused
Posts: 84
Joined: Fri Aug 20, 2010 7:35 am
Location: wiltshire

clutch

Post by BISH V8 » Tue Jan 21, 2014 8:25 pm

That's the same spec I've been advised, how do you rate it?
Current project
1972 mgb v8 4.6 roadster

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops » Tue Jan 21, 2014 9:03 pm

not bad clutch been using it for a few yrs now but need something a bit stronger once I go racing again.
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

BISH V8
Helpful or Confused
Helpful or Confused
Posts: 84
Joined: Fri Aug 20, 2010 7:35 am
Location: wiltshire

clutch upgrade (Tony)

Post by BISH V8 » Wed Feb 05, 2014 2:51 pm

With regards your clutch you used Tony CP2394-60 Cover and the CP2346-4 Driven plate, did you have the round nose bearing and also did you have any problem fitting to flywheel, I have been on to AP a dozen times and every time I ask a question I get a different answer, the latest from the technical side is that they don't know it will fit!! they are trying to sell me me the kit cp2000-13 but that only gives you a max of torque of 270llb, I am pushing 315lb of torque so wanting the 339lb uprated clutch. This is only a big issue because V8bloke (Mark) had such a hassle with fitting kit, it was wrong they ended cutting something off, the driven plate was to thick meaning it would have never worked, I think the driven plate thickness should be 8.38mm and I believe marks was 8.89mm.Its a hard life all I want to do is order a kit which fits, costs are 450 quid so I want it right...
Current project
1972 mgb v8 4.6 roadster

User avatar
Coops
Site Admin
Site Admin
Posts: 6184
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops » Wed Feb 05, 2014 4:11 pm

cluitch fitted straight on with no problems, and I think its the round nose bearing I have mate,
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Rotrex C38-91 supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 404 RWHP, (4.6)
New Forged 4.8 V8 kitted out with the dogs Cajones of parts and a procharger D1SC. 2017 :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

Post Reply

Return to “Drivetrain & Transmission Area”