AP hydraulic concentric slave bearing
Moderator: phpBB2 - Administrators
- Seight-V8
- Knows His Stuff
- Posts: 559
- Joined: Sun Jul 01, 2007 10:12 am
- Location: https://t.me/pump_upp
- Contact:
AP hydraulic concentric slave bearing
hello all,
Silly question maybe...but I cant find the answer.
My AP concentric throw-out bearing CP6859-54 has just arrived....
It has two ports on in, I am presuming on is for the hydraulic pipe, and the other is for a bleed nipple.
But its not been supplied with a nipple, just two empty ports.
Instructions do not say anything other than they are M10 hydraulic connections.
I've found a picture here.....that has two hydraulic pipes attached....where does the second one connect to in this case?.
http://www.v8wizard.com/Tremec_T5.php
cheers
scott
Silly question maybe...but I cant find the answer.
My AP concentric throw-out bearing CP6859-54 has just arrived....
It has two ports on in, I am presuming on is for the hydraulic pipe, and the other is for a bleed nipple.
But its not been supplied with a nipple, just two empty ports.
Instructions do not say anything other than they are M10 hydraulic connections.
I've found a picture here.....that has two hydraulic pipes attached....where does the second one connect to in this case?.
http://www.v8wizard.com/Tremec_T5.php
cheers
scott
- Seight-V8
- Knows His Stuff
- Posts: 559
- Joined: Sun Jul 01, 2007 10:12 am
- Location: https://t.me/pump_upp
- Contact:
-
- Forum Contributor
- Posts: 391
- Joined: Mon Nov 20, 2006 4:25 pm
- Location: Ashbourne, Derbyshire
I used a cp3859-54 on mine so very similar. Yes bleed nipple on end of hose, I got Earls to make up a hose for me with a bleed on the end. Don't forget the bleed port on the slave is the one that sits highest when installed or it is with mine.
Edit:
Here is my original Saab slave (pile of crap):
Here's my AP slave:
Mike
Edit:
Here is my original Saab slave (pile of crap):
Here's my AP slave:
Mike
- Seight-V8
- Knows His Stuff
- Posts: 559
- Joined: Sun Jul 01, 2007 10:12 am
- Location: https://t.me/pump_upp
- Contact:
yes that's the same one as I just bought.
I'll have to have a make up spacer under the bearing housing, as I'm using the TVR bell housing, I've drawn up a cad model of the set up, and just need to get the gearbox nose cut down and the spacer made next.
Thinking off using braided hose on mine though, just for ease...
Did you use copper pipe all the way to the master cylinder?
cheers
scott
I'll have to have a make up spacer under the bearing housing, as I'm using the TVR bell housing, I've drawn up a cad model of the set up, and just need to get the gearbox nose cut down and the spacer made next.
Thinking off using braided hose on mine though, just for ease...
Did you use copper pipe all the way to the master cylinder?
cheers
scott
-
- Forum Contributor
- Posts: 3979
- Joined: Sat Nov 18, 2006 6:22 pm
- Location: Northern Ireland
- Seight-V8
- Knows His Stuff
- Posts: 559
- Joined: Sun Jul 01, 2007 10:12 am
- Location: https://t.me/pump_upp
- Contact:
-
- Forum Contributor
- Posts: 3979
- Joined: Sat Nov 18, 2006 6:22 pm
- Location: Northern Ireland