Search found 10 matches

by durhamsmudger
Sun Aug 19, 2018 5:28 pm
Forum: Electrical & Ignition Area
Topic: 14CUX ECU help
Replies: 14
Views: 1145

Re: 14CUX ECU help

Yes, I sent the ECU away to Mark Adams, unfortunately the tests proved there was nothing wrong with the ECU-which was bad news, I did however use the opportunity to upgrade the chip from an Optimax to a Tornado, so then it was back to multi meter fault testing. I finally traced a cable fault to the ...
by durhamsmudger
Wed Dec 27, 2017 2:46 pm
Forum: Body & Strengthening
Topic: Epoxy Primer + Chassis Black
Replies: 6
Views: 2325

After blasting, bare carbon steel should have a protective coat applied within 4 hours ( this is in a dry environment) after this time oxydisation starts This is why the blasters apply some sort of coating.
by durhamsmudger
Fri Dec 22, 2017 6:22 pm
Forum: Electrical & Ignition Area
Topic: Fuel pump relay
Replies: 5
Views: 407

One relay is a simple on off which ois what you want , the other when it switches to off also goes to earth so you end up with a dead battery
by durhamsmudger
Tue Nov 28, 2017 11:14 pm
Forum: Electrical & Ignition Area
Topic: 14CUX ECU help
Replies: 14
Views: 1145

This is on a '99 Morgan 3.9, with the same type of ECU fitted to the TVRs of the era Ok a brief history About 6 months ago I started having intermittent problems with the fuel pump not starting,there is nothing wrong with the pump The green immobiliser box is communicating to the ECU OK The spider u...
by durhamsmudger
Mon Nov 27, 2017 10:11 pm
Forum: Electrical & Ignition Area
Topic: 14CUX ECU help
Replies: 14
Views: 1145

14CUX ECU help

I have a problem with my Morgan ECU, can anyone on this forum recommend a good reasonably priced company that can test & repair
Cheers
by durhamsmudger
Fri Sep 08, 2017 6:04 pm
Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
Topic: Rover 3.9 hot wire CO
Replies: 4
Views: 772

Sorry shouldve pointed out, this is with Cat's
by durhamsmudger
Thu Sep 07, 2017 1:21 pm
Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
Topic: Rover 3.9 hot wire CO
Replies: 4
Views: 772

Rover 3.9 hot wire CO

HI
can anyone advise what the CO reading should be for a 3.9 Hotwire engine
cheers[/b]
by durhamsmudger
Mon Mar 07, 2016 2:48 pm
Forum: Engines Area
Topic: Range Rover Valve Stem Seals Query
Replies: 7
Views: 1674

Thanks for all the posts, after I fitted the new oil seals ( using a drill press) Ive came to the conclusion the seals were not fully home as the remaining ones came off easily with a screwdriver , yet i have had to remove old ones in the past with mole grips
cheers
by durhamsmudger
Thu Mar 03, 2016 9:03 pm
Forum: Engines Area
Topic: rubber sump gasket
Replies: 23
Views: 3782

Like Perry Stephenson , I use sealant along with a Cork gasket, the only difference is, I use a VW sealant called Dirko. The advantage of this sealant I'd that when you come to remove the sump a light clout withave a rubber males breaks the seal , what is more, the old gasket /sealant is easily remo...
by durhamsmudger
Thu Mar 03, 2016 8:43 pm
Forum: Engines Area
Topic: Range Rover Valve Stem Seals Query
Replies: 7
Views: 1674

Range Rover Valve Stem Seals Query

Hi I'm looking for some experienced recommendations. I've got a 3.9 hot wire Range Rover Engine in my Morgan +8, about 8 years ago (25k miles) I fitted 2 heads along with a (Crane) high lift cam & double valve springs, over the last year or so I have been burning oil which has been getting progressi...

Go to advanced search