Search found 193 matches
- Mon Jan 07, 2019 7:26 am
- Forum: Engines Area
- Topic: Speedi Sleeve
- Replies: 1
- Views: 1312
Speedi Sleeve
Hi, A belated Happy New Year to everyone, I am after a Speedi Sleeve for my crankshaft pulley as mine has groove in it worn by the seal, who would thought rubber could do this ! I have fitted these to other engines in the past ( not Rovers ) and this has fixed the problem. Anyone know the size I nee...
- Mon Aug 29, 2016 10:06 pm
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley Or Facet Fuel Pump
- Replies: 5
- Views: 3405
Holley Or Facet Fuel Pump
Hi, My Facet Red Top fuel pump has just shat itself this evening, outside lane of the A1 of all places ! while I am replacing it do you gents think its worth going for a Holley Blue top ? Or stick with a red top facet ? A few details....Rover 4.6 with a weber 500 used for street use and pump mounted...
- Wed Jun 15, 2016 5:56 am
- Forum: Engines Area
- Topic: Oil pump question
- Replies: 7
- Views: 3631
Hi, I fitted one of these from V8 Tuner about 7 or 8 years ago now and it's been fine. Had to flap about a bit pressing drive gear on and off shafts as gears are deeper than standard SD1 and the shafts are different. I also had to fab a timing pointer and rework the dizzy clamp all simple stuff thou...
- Thu Mar 10, 2016 6:37 am
- Forum: Engines Area
- Topic: Mystery Engine Number
- Replies: 17
- Views: 6733
- Tue Mar 08, 2016 9:10 pm
- Forum: Engines Area
- Topic: Mystery Engine Number
- Replies: 17
- Views: 6733
- Tue Mar 08, 2016 5:35 am
- Forum: Engines Area
- Topic: Mystery Engine Number
- Replies: 17
- Views: 6733
- Mon Mar 07, 2016 7:21 am
- Forum: Engines Area
- Topic: Mystery Engine Number
- Replies: 17
- Views: 6733
Mystery Engine Number
Hi, Been asked by a fella over on a TR7 forum I am on to help I.D a engine number for him, it is - 46A00708A Its a late 3.9 / 3.5 block with cast crossbolts BUT not tapped, fitted with a SD1 type front cover, you can see that the engine number has been machine stamped into the block and has a compre...
- Mon Aug 18, 2014 6:05 am
- Forum: General Chat Area
- Topic: Spares, anyone used this?
- Replies: 3
- Views: 1432
- Thu Feb 20, 2014 8:02 pm
- Forum: Brakes & Suspension Area
- Topic: SD1 - TR7 Rear Disc Brake Bracket
- Replies: 14
- Views: 17334
Hi, My TR7 V8 has Audi Quattro callipers, mounted using homemade adaptors, Montego / Maestro discs, I had to turn down the ends of the half shafts so they fitted inside. The handbrake cables are Golf Mk 4 with a home made adaptor to fit to the standard lever. A couple of pictures taken during mockin...
- Mon Jan 14, 2013 6:36 pm
- Forum: Drivetrain & Transmission Area
- Topic: TR7 rear axle rebuild
- Replies: 3
- Views: 3268
Hi Markus, The worse bit is the fact you cant get the collaspesible spacer for the pinion pre load adjustment and the huge spanner you need to undon on the pinion. I made up a 'special tool' to hold the pinion still whilst undoing this nut http://i155.photobucket.com/albums/s300/john215_bucket/Danii...
- Mon Oct 15, 2012 6:31 am
- Forum: Electrical & Ignition Area
- Topic: 4.6 Starter Motor
- Replies: 9
- Views: 2582
- Sun Oct 14, 2012 6:31 pm
- Forum: Electrical & Ignition Area
- Topic: 4.6 Starter Motor
- Replies: 9
- Views: 2582
- Sun Oct 14, 2012 4:27 pm
- Forum: Electrical & Ignition Area
- Topic: 4.6 Starter Motor
- Replies: 9
- Views: 2582
4.6 Starter Motor
Hi, I thinking about fitting a Range Rover P38 starter motor to my 4.6 that i have in my TR7, at the moment it has a tired SD1 starter motor in it. My question is, i have two connectors on the solenoid on the SD1 motor, one to switch the solenoid the other to by pass the ballast wire for starting. D...
- Wed Jun 27, 2012 9:08 pm
- Forum: Forced Induction
- Topic: Single Turbo Rover V8 3.5 Triumph TR7 Build
- Replies: 37
- Views: 28122
- Sat Jun 09, 2012 6:22 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Edelbrock 1404 air filter stud
- Replies: 5
- Views: 4321