Page 1 of 2
i made a boo boo
Posted: Sat Jul 11, 2009 8:19 pm
by Coops
Hi guys,
made a bit of a cock up
ordered some plugs to fit the knock sensors which arrived,
not thinking that the new knock sensors would be different being O/E rover fittment,
but yes,
the junior timer plugs i ordered for the knock sensors fit the blue ones that screw into the block,
but not the ones that are bolted to the block, (that i bought and have here now
)
any one know what ferkin plugs i need now to wire them up please
Posted: Sun Jul 12, 2009 12:38 pm
by katanaman
Pic would be good T
Posted: Sun Jul 12, 2009 7:58 pm
by Coops
i aint got the knock sensors here mate they are on the engine, but these are the ones im using,
Posted: Sun Jul 12, 2009 8:25 pm
by stevieturbo
A pic of the plug would help..
At worst, either use small spades, or just solder wires onto the sensor.
Posted: Sun Jul 12, 2009 8:40 pm
by Coops
the plugs i bought are the same ones as used by ford crank sensors,
(junior timer plugs they are called) and the blue round screw in type rover knock sensors,
but they wont fit the new sensors im now using above.
Posted: Sun Jul 12, 2009 8:42 pm
by stevieturbo
Thats why I asked for a pic of the plug on the sensor lol...
Or just stick with the blue sensors.
Posted: Sun Jul 12, 2009 8:47 pm
by Coops
mmmmm
are there different sensors like these?
as thats what i asked for and though i had got,
but the ones i have on the engine have small tags on the edges like the first picture and not a plug socket like these,
part number for the ones i have are:
Part number NSC100650
Posted: Sun Jul 12, 2009 8:59 pm
by Coops
i want to use the newer style ones mate as they sit closer to the block etc,
i'll have to wait till next weekend to get any pics.
Posted: Sun Jul 12, 2009 9:04 pm
by stevieturbo
thev8kid wrote:mmmmm
are there different sensors like these?
as thats what i asked for and though i had got,
but the ones i have on the engine have small tags on the edges like the first picture and not a plug socket like these,
part number for the ones i have are:
Part number NSC100650
Not really sure of your question ??
Are you asking are the sensors like the sensor in the photo, with part number clearly listed ??
Lots of vauxhalls use Bosch with a normal 2 pin plug. Although loads of cars probably do too.
But whats wrong with using the blue rover sensors ?
Posted: Fri Jul 17, 2009 5:09 pm
by Coops
a pic of sensor and the plugs i bought (wrong)
Posted: Fri Jul 17, 2009 5:11 pm
by Coops
just noticed the ones i have dont look like the ones i want thats why the plugs dont fit,
Posted: Sat Jul 18, 2009 6:41 pm
by katanaman
I have seen them before they are called total seal or something like that. Basically they are a waterproof connector. Pretty sure vehicle wiring products stock them although you might have to buy both the plug and the socket.
Posted: Sat Jul 18, 2009 6:45 pm
by katanaman
Yes they do
http://www.vehicle-wiring-products.eu/V ... o/swp5.jpg unfortunately thats a 4pin so its hard to tell if it is actually the proper connector. Pretty sure they are the same that is all over my focus engine bay if you fancy a trip down the scrap yard.
Posted: Sun Jul 19, 2009 12:42 pm
by Coops
sorry been away for the weekend so now back on catching up,
the sensors i need are bosch 0 261 231 006
the ones i have been sold are 0 261 231 140
i think the first number are the ones i need for the v8, (as per the rpi pic)
not sure what the second fittiment is BUT they are in landrover box's
Posted: Thu Aug 06, 2009 3:33 pm
by Coops
right looks like im going to have to make do with the blue ones,
as I have contacted 3 landrover parts and none of them have the style knock sensor listed,
Have mailed partrange asking what fitment they are for what they are selling on ebay for the RV8 and no reply,
