Page 1 of 1
spigot bush
Posted: Sat Feb 09, 2008 2:56 pm
by bodger
sorry if it has been asked before but dos' any one know the part number for the bush , 3.5 v8 to lt77 ? ... i think it's a 12mm dia tip on the gearbox
?
thankyou
Posted: Sat Feb 09, 2008 3:37 pm
by davemgb
Rimmer V8 catalogue lists 614263 for saloon and sports with manual transmissions.
Dave
Posted: Sat Feb 09, 2008 5:08 pm
by bodger
thankyou Dave , i was wondering if there was a rover part number for it too ?
Posted: Sat Feb 09, 2008 8:54 pm
by ChrisJC
That is a Rover part no. Rimmers use the Rover numbers, which is handy as some parts don't appear on their website, but if you use the 'Prices' page you can just stick in any old rover part no, and they might have it!
Chris.
Posted: Sat Feb 09, 2008 10:23 pm
by bodger
thankyou chris ,
the next thing i'm after is the higher ratio 5th gear pair , the box i have now has the 36/20 set which gives me 0.833:1 and i'm after the later 37/19 which will give me the 0.77:1
Posted: Sat Feb 09, 2008 11:02 pm
by CastleMGBV8
Bodger,
Real Steel have them in stock £8.08!.
Re you fifth gear set the ratios quoted on my spec sheets give the early set as .82/1 and the later which I have as .78/1 which gives me 2256RPM at 70MPH, the .82 would give 2371RPM at 70MPH so not a lot of difference.
This is with a 3.07 diff and 195/65 x 15" tyres.
Kevin.
Posted: Sun Feb 10, 2008 12:53 am
by bodger
the ratios that i quoted are for the box i have with the 22/33 primary set
which then gives a conversion factor of 1.5 ... so that 19 divided by 37 times 1.5 then gives me the 0.77:1
i'm only changing them because it's a TR7 box that i have got and as it's stripped i might as well do it
all the other ratios are SD1 V8 spec , it just has the earlier 20/36 5th gear
i'll check "real steel" on monday , thanks for that Kevin
this is in my van remember i dream of 70 at 2300 revs ..lol
Posted: Sun Feb 10, 2008 9:58 am
by CastleMGBV8
Bodger,
Yes your down near Erith, your rocker covers are going on to my new engine once I get them cleaned and polished.
If it's broke then you may as well fix it. If I remember corrrectly you had a spare late LT77 with the larger main input shaft, that should have the higher 5th ratio. If you still have it check the number in the sticky gearbox numbers.
Kevin.
Posted: Sun Feb 10, 2008 11:07 am
by bodger
Hi Kevin , yes thats me , i sold those 2 boxes i had in the bedroom and bought another one , a TR7 lt77 this time , i have an old sherpa box in the van at the moment with as you say a larger spigot tip , i thinks it''s 7/8" so i have no bush in the crankshaft at the moment ... aagghhh
acording to the LDV/sherpa manual i have it has the 0.83: 1 ratio on 5th
Posted: Sun Feb 10, 2008 11:35 am
by CastleMGBV8
Bodger,
If you can tell me the rear axle ratio and the tyre size I can give you the exact MPH/RPM.
Kevin.
Posted: Mon Feb 11, 2008 10:16 am
by bodger
CastleMGBV8 wrote:Bodger,
Real Steel have them in stock £8.08!.
Re you fifth gear set the ratios quoted on my spec sheets give the early set as .82/1 and the later which I have as .78/1 which gives me 2256RPM at 70MPH, the .82 would give 2371RPM at 70MPH so not a lot of difference.
This is with a 3.07 diff and 195/65 x 15" tyres.
Kevin.
Hi Kevin , real steel only do engine bits , no gearbox stuff
Posted: Mon Feb 11, 2008 11:42 am
by CastleMGBV8
I've just bought a spigot bush from them! should arrive in the post today.
Kevin.
Posted: Mon Feb 11, 2008 12:13 pm
by bodger
oops sorry , i thought you meant the gears ....
got one from Rimmers , £7.00 + p&p ...it turned up next day