solenoids

General Chat About Nitrous Oxide.

Moderator: phpBB2 - Administrators

Post Reply
User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

solenoids

Post by JSF55 »

Do they have to be mounted upright? and is it possible to use flexi lines to supply to the jets so they can moved out of the way a bit :?


So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

They can be mounted any way really. There are some basic rules for the ay the fuel solenoids should be fitted. mainly to ensure air naturally vents out of the fuel line before the solenoid and the solenoid itself.

What system are you using ??
Got any pics??

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

Post by JSF55 »

Hi Perry, it's an edelbrock one, but the solenoids stick out the front and back of the carb, noticed on ebay a kit with flexible lines, i'd like to mount them more to the rear possibly under the coil packs ?
Image
Image
So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

OK!
So its a sniper or cheater kit etc...
Is that a pressure reg between the fuel filter and the solenoid??
If you have tapped off the 5psi supply for the carb from the same pump that wont be needed. Or do you have a separate pump running higher psi for the nitrous fuel supply ??

The main thing to think about is fuel delivery. If you run nitrous at 800-1000 psi then the speed of that nitrous will get to the plate in a heartbeat. But petrol running at 5-6 psi will take an age to get to the plate. You need to make sure that the petrol and gas hit at the same time, or even make sure the petrol gets there a bit before the gas??

Give us some more info on:
Fuel pressure.
Nitrous pressure control (bottle heater etc)
How much gas you want to flow.
How long is the line from nos bottle to engine.

Perry

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

Post by JSF55 »

Hi perry, yeah sniper kit, i only wanted to move the solenoids as they look pant's where they are ! but as your asking :lol: seperate supply from the tanl through a facet solid state pump... err 6 psi ? to the regulator and filter in 8mm pipe. nitrous line is standard kit length , about 4m ? and the bottle just sits in the boot empty :shock: i've got a rebuilt engine going in towards the end of next month and that will need running in, it'll probably the end of september at the hot rod drags before it's used, oh it's set for a 50bhp shot ..... sh!t i've already asked that :shock:
http://www.v8forum.co.uk/forum/viewtopi ... ht=nitrous
So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

OK!
You need to go back to basics now. And you will need to do some basic flow testing. I know this sounds like a bit of a faff. But if you want the best results then you need to get this poop sorted before you go on track really..

Ditch the fuel pressure regulator for a start.
Then fit a fuel pressure gauge in its place.
Then pull the plate of the engine so you can flow fuel through the fuel jet and out of the spray bar into a big jug.

You need to operate the solenoid and see how much fuel flows into the jug in 10 seconds and also monitor the fuel pressure on the gauge while doing this.
Make sure you have purged all the air out of the fuel line up to the solenoid before you do this test.

Make sure that you do the test for a proper 10 seconds and let us know how many ml's of fuel you flowed and at what pressure. This will tell us the actual hp amount of fuel you have flowed.

Once we know how much fuel you can flow on the 50hp fuel jet we can talk about the nitrous side of the system..

If you have the stock 4metre -4 size braided hose with the bottle in the boot you will need to make sure that the bottle pressure is at least 850 psi before doing a flow test on the nitrous.

Perry

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

Post by JSF55 »

Cheers perry, i'll come back to this later in the year, no point on starting something i can't finish ! i just remembered there was a hold up on the SPV which left me with no time to finish it :(
So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

SPV ??

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

Post by JSF55 »

Safety pressure valve? maybe there called something else?
So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

Are you talking about the wizards of nos SPRV??

This will replace your old bursting disk on the bottle valve.

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

Coops
Site Admin
Site Admin
Posts: 6317
Joined: Fri Nov 17, 2006 7:43 pm
Location: Newbury, Berks
Contact:

Post by Coops »

thats what i must do at some point,
change the rupture disc to the SPRV valve.
Regards Tony C (COOPS)
Image
MS2 V3.57 Ecu mapable efi and wasted spark ignition.
Procharger D1SC supercharger and Cossie RS500 Intercooler @ 14psi of Boost. 416 RWHP, (boost leak)
Forged 4.8 V8 kitted out with the dogs Cajones of parts. :D
Sponsored by: www.v8performanceparts.co.uk, www.interpart.biz, www.caprisport.com & www.baileyperformance.co.uk

User avatar
JSF55
Forum Contributor
Forum Contributor
Posts: 991
Joined: Mon Dec 04, 2006 4:15 pm
Location: Swansea
Contact:

Post by JSF55 »

Yep spv. . . spectrum pursuit vehicle :lol: there was no rupture disc fitted, it had a gauge screwed in instead :shock: so wouldn't chance it till ia arrived a little late :(
So thats where it went !

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

Good move mate!!

A gauge instead of a safety valve :lol:

I've converted a few of my bottles to sprv's now.

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

Post Reply

Return to “Nitrous Oxide Area ”