Search found 105 matches
- Wed May 08, 2013 6:55 pm
- Forum: Electrical & Ignition Area
- Topic: Rumble in the force
- Replies: 25
- Views: 5149
Rumble in the force
There is a rumble low in the revs on my 3.5 Land Rover V8.Feels like a bit off a stutter. I replaced the coil ( one month in use and it leaked oil) sent the company a email to complain... New spark plugs, leads, cheked the distributor cap. Set the ignition @ 8 degree before ( car only runs on lpg) C...
- Sat Mar 16, 2013 8:36 am
- Forum: Electrical & Ignition Area
- Topic: Powerspark
- Replies: 9
- Views: 2338
Powerspark
I fitted a new coil from http://www.simonbbc.com/powerspark-ignition-coil A big difference, the spark is mutch brighter and starting is much better. Even today 1 clik and vrooooaaaam it also idles much better !! 8) ( start on lpg no gas tank anymore) I always thougt that a coil could not become weak...
- Sat Mar 16, 2013 8:31 am
- Forum: Engines Area
- Topic: 3.9 Rover rebuild
- Replies: 2
- Views: 1704
- Sun Mar 10, 2013 8:04 am
- Forum: Engines Area
- Topic: 3.9 Rover rebuild
- Replies: 2
- Views: 1704
3.9 Rover rebuild
A friend of mine is rebuilding a 3.9, he bought it from e bay and on arrival the engine was totaly locked, very hard to turn by hand. He dismanteld and cleaned al the parts so good he now doesn't know anymore witch piston goes were. Even the drive rods end caps are mixed. When he started to reasembl...
- Sat Sep 08, 2012 4:57 pm
- Forum: Cooling Area
- Topic: Not cool enough
- Replies: 19
- Views: 10626
- Sat Sep 08, 2012 6:35 am
- Forum: Cooling Area
- Topic: Not cool enough
- Replies: 19
- Views: 10626
Still trying to post a pic
http://i47.tinypic.com/n7ryc.jpg
I think my problem is that i don't have a plate around the tunnel. I called land rover to get a origenel one, to much money for me, will make my one
http://i47.tinypic.com/n7ryc.jpg
I think my problem is that i don't have a plate around the tunnel. I called land rover to get a origenel one, to much money for me, will make my one
- Sat Sep 01, 2012 6:14 pm
- Forum: Cooling Area
- Topic: Not cool enough
- Replies: 19
- Views: 10626
EFI models have a viscous fan that 'locks up' when hot. Needs the later matching water pump. But it is more efficient than the normal viscous one. The one i have is locked up enough i think, no way of stopping it with a plastic bottle. Just tested that with the bonnet open in doesnt overheat, when ...
- Sat Sep 01, 2012 2:08 pm
- Forum: Cooling Area
- Topic: Not cool enough
- Replies: 19
- Views: 10626
Once it is hot and you start driving again how quickly does the temperatue drop? Ian This depends on the weather. Quick enough when i also use the heater fan. Without the heater fan if street use after 1 a 2 kilometer. My fan is a visco and it works, it tried to stop it with a plastic bottle. I tho...
- Fri Aug 31, 2012 3:29 pm
- Forum: Cooling Area
- Topic: Not cool enough
- Replies: 19
- Views: 10626
Not cool enough
After winching and getting stuck with the def V8 the temperature rises very fast and hard. I have a autobox fitted and the cooler sits directly in front of the rad ( transaver cooler) If i drive no problems, if it sits stil even at idle the temp rises. Unless i keep the bonnet open. So wath to do ? ...
- Sun Jan 29, 2012 10:17 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902
Just did a testrun, it is just freezing so the box is cold. Everything just workt fine, with the engine warming up the gearbox also got smoother. The only thing a hear is a bit of a noise coming from the torque convertor- gearbox. I hear it only on idle Sounds like a cluth release bearing. (i know t...
- Sun Jan 29, 2012 9:38 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902
As those boxes get old, the clutches wear. The particles should get picked up by the filter. Eventually however, they get into the governor, which then causes the 'box to 'hang' in a low gear, sometimes just staying in first. It tends to clear up as the box warms up. Chris. I placed new oil and fil...
- Sat Jan 28, 2012 9:46 pm
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902
Nothing helped i tried many hours. A friend of mine came over and when i took him for a testrun everything worked just fine :shock: :D Perhaps some air in the governor ? Mabey something that the valve has been sticking inside the box. Very strange... The combo off the crower camshaft and the autobox...
- Fri Jan 27, 2012 1:29 pm
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902
I placed the kit on my V8, looks great however on the testdrive i found that. It does not shift up, when i release the throttle it shifts up. :roll: When i the put my feet a bit to hard on the gas it shifts down however is doesnt shift up anymore. I stays to long in one gear and the engine is draggi...
- Mon Jan 23, 2012 1:43 pm
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902
- Mon Jan 23, 2012 8:15 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Holley with ZF kickdown bracket
- Replies: 17
- Views: 6902