2 stage on a rover

General Chat About Nitrous Oxide.

Moderator: phpBB2 - Administrators

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

2 stage on a rover

Post by bones »

Hi all, what is the max a rover 3.9 will take of gas, 1st stage would be between 25 and a 50 shot, 2nd ???, ive heard rovers dont like a 100 straight of the button, but going 2 stage what is the max, i suppose this is one for you to answer Pel,but all advicwe is welcome :D rich



mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

Hi Rich
I'll do that wiring diagram for you shortly.

When I did my 1st ever 3500 build I was told by Real Steel that a 75shot would be max for the engine.
But I fitted a 2 stage plate setup (holley) and ran 50+100 with no probs apart from traction issues. The engine was a bit detuned to run gas though. Kept the low 8:1 comp etc.
Then swapped to the Wizards setup with a controller and she ran quicker with just a 100 shot of gas. So I know an old low comp V8 will take up to 150 of gas ok. The beauty of your car is that its auto. So the hard hit of the gas tends to get softened out by the tranny. But you need to make sure the tranny can handle the increase in power.
I dont see why you could not do a 50 shot off the line on the pedal switch, then stick another 50-75 on with a button once you get to 2nd gear. I would start with 25+50. Then try 50+50.

I've now got the 4.6 which is stock apart from the cam and my home porting etc. As you know I'm running 200, 225 and 250 shot while I'm experimenting.

Tail end of last year I had a wiring fault at the track and bypassed the controller to a push button. This is my lad sticking 200 on just after he gets rolling.


Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

the tranny should be fine,it was built with nitrous in mind and the torque was made for it, Thanks for the wiring diagram Pel much appreciated. another ??, what is the difference between a 37 deg AN and a 45deg AN, thats what on the nos web site, is it just the angle or something to do with the threads?? :)

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

It will no doubt be the angle of the cone shaped bit of the fitting.
I've only ever used -4an fittings. I've bought them from all over the place. But I've never been asked what angle I want?

Have you got a link to the info on the website?

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

one place was exupracing, they do some cheap stuff, but im off to websters on monday to pick up some other stuff and they do the parts i need, anyone ever used cold fusion nitrous parts?? :) rich

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

Hi all, what jet sizes do i need for a 25 shot of gas??. :) rich

User avatar
topcatcustom
Forum Contributor
Forum Contributor
Posts: 2965
Joined: Sat Aug 09, 2008 11:53 am
Location: Essex
Contact:

Post by topcatcustom »

:lol: Perry I absolutely love that video! Going for 2 stages now then rich?

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

i thought i would give it ago, ive got to keep up with you supercharged boys, and my system doesnt like being pulsed ,and it will be done for retro day, all the bits turning up this week that i still need, just trying to find the jet sizes for a 25 shot :D rich

bobtail84
Forum Contributor
Forum Contributor
Posts: 175
Joined: Mon Apr 27, 2009 4:26 pm
Location: Westcliff-on-Sea. Essex. UK

Post by bobtail84 »

I also loved that vid. 8-) It made the hairs on the back of me neck stand up.

Jeff

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

Rich!
I left you a voicemail with 50,75 and 100 shot jet sizes for a sniper plate. I'm not sure if yours is a cheater plate so I'll get that info tomorrow most likely.

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »


Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

ive got 2 cheater plates,that is if the cheater plates have loads of holes in the tubes??, bottom plate 1st stage, top plate 2nd stage, ive got some old jets which i was told are a 50 shot 032 and 043, ive got jets for 75 and 100 and 125 shot, i know a 25 shot is low, but i havent got a lsd axle and only road tyres, if they hold i will try 50 on 1st stage, although ive heard real steel has got 25 shot jet sizes in :) rich

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

well the 2 stage worked once at retro due to low pressure, just weighed the bottle ,when empty 15lb it is 16.8lb so that explains the low pressure all day :( , not to worry nth weald in 2 weeks and a full bottle to play with, :D rich

User avatar
bones
Forum Contributor
Forum Contributor
Posts: 1551
Joined: Wed Nov 22, 2006 10:08 am
Location: essex

Post by bones »

old post revisited. well the 2 stage works fine for me but know i need more gas, with traction 1st stage will be 50, 2nd stage would it be ok with a 100 or 125 shot once in 2nd gear or to risky. rings have been opened, plus its an auto box. Due to no traction at nth weald at the moment these are the settings, 1st is 35 and 2nd is 75. any thoughts peeps :D rich

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

""the 2 stage works fine for me, but know i need more gas""

:lol: :lol: :lol:

He's got the Bug 8)

Rich!
As long as you have good tyres and can get some grip I dont see why you cant hit a 50 off the line and stick a 100+ on in 2nd gear ??

But for Gods sake do some fuel flow testing.
Remind me again of the fuel system you have?? What pump for the nos side?? What size fuel lines from pump to the engine bay / regulator etc.. Give us a blow by blow account of what you have from the tank to the fuel solenoids??

You are running nos plates so the jets are at the plate inlet connections arent they?
This makes it difficult to do accurate fuel flow testing unless you can lift the plate out over a bowl to catch the fuel and measure it?

You need to be able to flow 100ml's of petrol in 10 seconds per 100hp as a rule of thumb. This should give you a slightly fuel rich setting.

Get it right at this stage while flow tersting on the driveway and you can avoid some nasty mishaps :)

Rich is good!
By that I mean the petrol flow, not you ;)

If you can max out your system by running fat you can always tune back the fuel to match the gas on small systems like ours.

Pel

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

Post Reply

Return to “Nitrous Oxide Area ”