Tricky"s TR7 V8 as seen in PPC Magazine

Is Your Car Being Featured In A Magazine? Let Us Know Here :D

Moderator: phpBB2 - Administrators

Boosted LS1
Knows His Stuff
Knows His Stuff
Posts: 518
Joined: Thu Nov 23, 2006 12:05 am
Location: Nottingham, Notts, England, UK
Contact:

Post by Boosted LS1 »

Tricky wrote:Thanks for helping with pics, i am running a standard TR7 axle with LSD 3:9 ratio i want to change to a ford 9" with a 3:5 diff my axle wont last long need to change gearbox to but to what? been told Supra gearbox is strong i want to stay manual, my engine is running a set of alloy rods
What bits might you get rid of ?
My axle survived and my engine was turbocharged. It didn't do many miles though, sunshine car :) That said it would break traction before I broke anything. I pegged the tubes to the diff housing which may have helped. I used an lt77 built by Ken Tomlinson (he built the axle to) and it survived. Now I'm building again intending to use a TH400 and an 8.8". The axle is about 2" wider then the tr7 axle and the one I bought has rear discs and wheel sensors. Supra 5 speed is strong and comes in several versions or the TKO 600 would do. Guess cost comes into the equation. Or you could use a TH350 with manual shift. That would be cool, strong and you could play with it. I'm planning to sell my axle and it's fitting linkage.


Image

Tricky
Helpful or Confused
Helpful or Confused
Posts: 106
Joined: Sun May 17, 2009 9:12 am
Location: oxfordshire

Post by Tricky »

Hi Boosted thanks for that info.How much for your axle?????
Tricky

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

That's really interesting Boosted??

A Salisbury with a better ratio than mine. How does one come across a TR7 axle like this?? How much will yours be when it goes on sale?? Is the TR7 axle much different in width to the MGB Salisbury??
We need to talk I think.

Tricky.
My axle is the MGB V8 Salisbury with 3.07:1 ratio. I'm using a TH350 3 speed with a ratchet shifter. Mine is putting a chunk over 400 ft/lbs and the box has been mint for the last few years. And so has the old axle. But my engine is not built to rev like yours. My max rpm is 6000 and up there its doing nowt. All my torque is down in the 4000-5000 rpm area. And I'm crossing the line at just over 5000 rpm.

The Salisbury axle is a very strong unit isnt it. Well underestimated by many folk.

Perry

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

mgbv8
Forum Contributor
Forum Contributor
Posts: 5326
Joined: Sat Nov 18, 2006 7:57 pm

Post by mgbv8 »

Flippin 'eck Tricky....

Your quick off the line aint ya :D

Perry Stephenson

MGB GT + Rover V8

9.62 @ 137.37mph

Now looking for 8 seconds with a SBC engine

http://www.youtube.com/watch?v=nVscbPHgue0&list=UUqIlXfSAoiZ--GyG4tfRrjw



https://www.youtube.com/watch?v=eg3avnsNKrc&index=2&list=FLqIlXfSAoiZ--GyG4tfRrjw

Boosted LS1
Knows His Stuff
Knows His Stuff
Posts: 518
Joined: Thu Nov 23, 2006 12:05 am
Location: Nottingham, Notts, England, UK
Contact:

Post by Boosted LS1 »

I'd need to show you some pictures of the conversion. The car did about 3000 miles tops. The diff was a new 2.84 from a vitesse and the lsd was a new quaiffe item. Then there was a lot of work making the jigs to enable the 'A' frame to be made correctly. Then another jig was made to enable correct mounting points in the chassis to locate the trailing links. these have sphericals at one end and nylon top hats at the other end. The axle is done for coilovers. There's also a very substantial plate under the diff housing to reinforce it as this is where the 'A' frame attaches. It has a spherical bearing here to allow for body roll etc.

The idea's been covered in the Punn book, How to make your car handle. Well worth a read.
Image

Tricky
Helpful or Confused
Helpful or Confused
Posts: 106
Joined: Sun May 17, 2009 9:12 am
Location: oxfordshire

Post by Tricky »

Hi Perry not quick enough to beat you yet :lol:
Tricky

Post Reply

Return to “Magazine Features Of Members Car's”